This page contains a Flash digital edition of a book.
SMART ENERGY


Low-Cost Energy Saving Improvements in Metalcasting


CINDY BELT (LEAD AUTHOR), METALS ENERGY MANAGEMENT (CALLAHAN, FLORIDA), AND ROBERT EPPICH, EPPICH TECHNOLOGIES (SYRACUSE, INDIANA), BRIAN REINKE, TDI CONSULTING (LEMONT, ILLINOIS), AND DR. JAMES WICZER, SENSOR SYNERGY (VERNON HILLS, ILLINOIS) (CONTRIBUTING AUTHORS)


E


very plant would benefit from an energy program to continuously improve


efficiency. Such a program should include working toward major up- grades to improve energy efficiency of the processes and establishing a three-year plan for new and efficient equipment. But sometimes, smaller but easy projects can help metalcast- ers save energy too. Below are a few. Compressed air leaks—A sad fact is that most plants lose 20-30% of the compressed air produced to leaks. It is not unheard of to have even 50% of the air lost to leaks. Given the cost to find and repair leaks, zero leaks is impractical but a good goal is 10-20% leaks. Tese leaks can be found on down days when the plant is quiet. Or, use ultrasonic equipment to find the leaks anytime. A rule-of-thumb is that if you can hear a compressed air leak, it is costing you at least $700 per year. Gas leak survey—Just as com-


pressed air systems always have leaks, natural gas lines also leak. One-percent losses are normal, and even a 12% loss has been recorded in one plant. Tese leaks can be found using ultra- sonic equipment or gas sniffers. However, the quickest method is hiring a firm to use a special infrared camera that detects gas leaks. Tis camera is not a typical infrared and costs much more, so hiring a firm with expertise using the equipment can make sense. Conveyor heat loss—Every


This infrared image shows heat loss at the furnace door.


2,000 lbs. and saved $5,000 in energy costs for the year. Reduce door open time—Every time a furnace door is open, heat is lost. Facilities can reduce this time by adjusting the door opening and closing time, staging charges, and staging equipment such as skim- ming tools, etc. This can be a subject of a Kaizen event. Redirect fans—Many plants use


nance or plan it during weekends. By documenting what equipment (for example, heat treat furnaces, fans, baghouses, lights, and air compres- sors) should be shut down during this time will save energy. Tis can be a simple checklist. One plant put stickers on the switches that should be shut off. Tese procedures will help new personnel know what equipment should be shut off (and remind current personnel). Use infrared cameras—Infrared


cameras are used in many plants to detect hot spots in electrical systems. The same cameras can be used to observe the walls and doors of furnaces, looking for poor seals and defective insulation. Learn from the best—Look at


Every time a furnace door is open, heat is lost. Facilities can


data by shift. Which shift is more energy efficient and/or produces more product? Learn best practices from them and transfer the knowl- edge to other shifts. In one study, a shift was regularly producing 15% more product. Fully utilize the most


reduce this time by adjusting the door opening and closing time, staging charges, and staging equipment such as skimming tools.


time a product is heated in heat treat furnaces, the cart is also being heated. Te official term for this is conveyor heat loss. Business- es can reduce the weight of the carts to save on energy cost. At one plant, a 3,000-lb. grating was used to provide a flat surface when the cart began to warp. A redesigned grating trimmed


fans to cool personnel. Unfortunately, they are sometimes aimed at the fur- nace too. Tis air flow increases heat loss in the walls. Aim fans correctly. Document down-time procedures— Every plant has downtime for mainte-


energy efficient furnace— First, know which furnaces are best, then do everything possible to fully utilize them. Tis may include bet- ter scheduling or optimizing the process before and after that furnace. Air-fuel ratios—Check the air-fuel ratio on a scheduled basis. One reverb furnace operator was wasting $10,000 a month due to operating with dirty filters. Motors—Surveys have


shown numerous motors are


left running during periods of down- time or even weekends. Tousands of dollars are wasted. Document shut- down procedures or automate shut- downs, such as shutting off conveyors when there is no product.


March 2018 MODERN CASTING | 69


Page 1  |  Page 2  |  Page 3  |  Page 4  |  Page 5  |  Page 6  |  Page 7  |  Page 8  |  Page 9  |  Page 10  |  Page 11  |  Page 12  |  Page 13  |  Page 14  |  Page 15  |  Page 16  |  Page 17  |  Page 18  |  Page 19  |  Page 20  |  Page 21  |  Page 22  |  Page 23  |  Page 24  |  Page 25  |  Page 26  |  Page 27  |  Page 28  |  Page 29  |  Page 30  |  Page 31  |  Page 32  |  Page 33  |  Page 34  |  Page 35  |  Page 36  |  Page 37  |  Page 38  |  Page 39  |  Page 40  |  Page 41  |  Page 42  |  Page 43  |  Page 44  |  Page 45  |  Page 46  |  Page 47  |  Page 48  |  Page 49  |  Page 50  |  Page 51  |  Page 52  |  Page 53  |  Page 54  |  Page 55  |  Page 56  |  Page 57  |  Page 58  |  Page 59  |  Page 60  |  Page 61  |  Page 62  |  Page 63  |  Page 64  |  Page 65  |  Page 66  |  Page 67  |  Page 68  |  Page 69  |  Page 70  |  Page 71  |  Page 72  |  Page 73  |  Page 74  |  Page 75  |  Page 76  |  Page 77  |  Page 78  |  Page 79  |  Page 80  |  Page 81  |  Page 82  |  Page 83  |  Page 84  |  Page 85  |  Page 86  |  Page 87  |  Page 88